091 327 0770 - 090 326 2566
info@hdsteel.com.vn

Aluminum insulation jacketing: thickness by pipe size and sizing

Aluminum insulation jacketing (also called cladding) is the thin metal skin wrapped over mineral wool, glass wool or foam insulation on hot and cold pipes, tanks and equipment. It keeps out rain and sun, resists knocks and keeps the insulation dry; wet insulation loses most of its thermal value and lets the pipe underneath corrode. When ordering, insulators usually ask three things: how thick is enough, how much aluminum each metre of pipe needs, and which alloy to buy. This article answers all three with sourced figures.

Summary card of minimum aluminum insulation jacketing thickness by insulation outer diameter per ASTM C1729

Minimum aluminum jacket thickness by insulation outer diameter (compiled by H&D Steel)

Which standard covers aluminum jacketing?

In the US and in many industrial project specifications, aluminum jacketing follows ASTM C1729 (Standard Specification for Aluminum Jacketing for Insulation). According to a technical presentation by the National Insulation Association (NIA), C1729 was first approved in 2010 and incorporates the composition and property requirements of the sheet standard ASTM B209. The standard classifies jacketing along three axes:

  • Type – outer surface: bare, pigmented paint, clear paint, plastic film or PVdF paint.
  • Grade – alloy: 3105/3003, 1100, 3004, Alclad 3004 or 5052.
  • Class – interior moisture barrier: polyfilm, polykraft, painted or bare.

The full C1729 text is a paid document; the figures below come from two jacketing manufacturers' data sheets that reproduce the standard's table, and from the NIA presentation.

Minimum thickness by insulation outer diameter

According to NIA, the required jacket thickness in C1729 depends on two things: the outer diameter of the insulation (larger needs thicker) and the rigidity of the insulation (less rigid needs thicker). Insulation is "non-rigid" when its compressive strength is below 15 psi, about 103 kPa. The aluminum jacketing data sheets from ITW Insulation Systems (Pabco/Childers) and Johns Manville print the same minimum thickness table:

Insulation outer diameter Rigid insulation Non-rigid insulation
Up to 8 in (≈ 203 mm) 0.41 mm (0.016 in) 0.41 mm (0.016 in)
Over 8 to 11 in (≈ 203–279 mm) 0.41 mm 0.51 mm (0.020 in)
Over 11 to 24 in (≈ 279–610 mm) 0.41 mm 0.61 mm (0.024 in)
Over 24 to 36 in (≈ 610–914 mm) 0.51 mm 0.81 mm (0.032 in)
Over 36 in (≈ 914 mm) 0.61 mm 1.01 mm (0.040 in)

Three points to read correctly. First, the diameter is the outer diameter of the insulation, not of the pipe. A DN100 pipe (114.3 mm) with 50 mm of insulation is about 214 mm across, already past the 8 in mark. Second, NIA states the required thickness excludes coatings, embossing or corrugation; embossed sheet must be measured on the metal. Third, these are minimums. A nominal 0.4 mm sheet on the minus side of its tolerance falls below 0.41 mm, and 0.5 mm still falls short of 0.51 mm. If the specification cites ASTM C1729, go up one step.

Which alloy suits jacketing?

According to the ITW and Johns Manville data sheets, aluminum jacketing is usually made from 3105 or 3003. The two have similar composition and performance and are treated as interchangeable. Pure aluminum is soft and less suited to the job; adding manganese and magnesium and cold working make it stronger. The C1729 alloy list includes 1100 but not 1050. On building projects with no specification, soft and easy-to-roll A1050 is still widely used. If the drawing or tender documents cite ASTM C1729, order 3003 aluminum and ask for a mill certificate showing the alloy. A detailed A1050 vs A3003 comparison for insulation is in our article choosing A1050 or A3003 coil for insulation jacketing; 1050 data is on the 1050 aluminum sheet page.

For the outer finish, the ITW data sheet describes three options: smooth (sheds rain best but shows dents and glare), stucco embossed (hides scratches, slightly stiffer) and 3/16 in corrugated (noticeably stiffer, follows pipe movement better, up to 0.024 in thick). NIA notes the performance difference between them is small; the choice is mostly about appearance.

Interior moisture barrier: do not skip it

According to the NIA presentation, C1729 requires a moisture barrier on the inside of pipe jacketing, factory heat-laminated; glued-on barriers are not allowed. Polyfilm lets through more than ten times less water vapor than polykraft. The ITW data sheet gives the polyfilm as 3 mil (76 µm) thick and says it helps prevent pitting, crevice and galvanic corrosion between the aluminum jacket and a steel pipe. When buying plain coil to cut on site, this barrier has to be sourced separately.

Insulated pipe with aluminum jacketing lapped to shed water and secured with metal bands

Aluminum jacketing lapped to shed water, with the flange cover overlapping the pipe jacket — AI-generated illustration

Estimating aluminum per metre of pipe

The cut length of each sheet is the insulation circumference plus the longitudinal overlap: L = π × D + lap. The table assumes a 50 mm longitudinal lap, a 1,000 mm wide coil with a 50 mm circumferential lap (each sheet covers 950 mm of pipe), and a 3003 density of about 2.73 g/cm³ from the Dinco data sheet. Follow the drawing or project specification for actual laps.

Pipe + insulation Outer diameter Cut length m² of aluminum / m of pipe Chosen thickness kg / m of pipe
DN50 + 40 mm wool ≈ 140 mm ≈ 491 mm ≈ 0.52 0.5 mm ≈ 0.71
DN100 + 50 mm wool ≈ 214 mm ≈ 723 mm ≈ 0.76 0.6 mm ≈ 1.25
DN200 + 50 mm wool ≈ 319 mm ≈ 1,052 mm ≈ 1.11 0.7 mm ≈ 2.12

Thicknesses in the table follow the non-rigid column above plus a margin for tolerance. The total order is the weight per metre times the run length, plus an allowance for elbows, tees, valves and flanges, where cutting waste is usually higher than on straight pipe. Each millimetre of aluminum weighs about 2.7 kg/m², so 0.5 mm sheet is roughly 1.37 kg/m².

Five common mistakes in buying and installing

  • Sizing the thickness on pipe diameter instead of insulation outer diameter. A small pipe with thick insulation easily passes the 8 in mark unnoticed.
  • Buying sheet too thin for non-rigid insulation. Soft mineral or glass wool lets the jacket dent when stepped on, leaned on or hit by strong wind; use the non-rigid column.
  • Skipping the moisture barrier. Condensation between the jacket and a steel pipe causes corrosion that cannot be seen from outside.
  • Laps facing against the water flow. An article in NIA's Insulation Outlook stresses that jacketing must be lapped in a watershed fashion, upper edge over lower edge, so water runs off rather than in.
  • Valve and flange covers not overlapping enough. The same article advises extending the valve or flange cover over the pipe jacket by at least 2 in (about 50 mm) or the insulation thickness, whichever is greater, so the joint does not open when the hot pipe expands.

Conclusion

Choose aluminum insulation jacketing in three steps: measure the insulation outer diameter, decide whether the insulation is rigid or non-rigid, then take the minimum thickness from the table and add a margin for tolerance. If the specification cites ASTM C1729, use 3003 or 3105 with an interior moisture barrier. Coil sizes are on our aluminum coil and slit strip A1050, 3003, 5052 page.

References

For aluminum coil for insulation jacketing in 1050 or 3003, in the right thickness for your pipe sizes and with mill certificates, send a request via our aluminum coil and sheet quotation page or call hotline/Zalo 0904 678 236 (Sales Department) for advice on the right specification.


Bài viết liên quan

Nhôm bọc bảo ôn: chọn độ dày theo đường kính ống và cách tính

Nhôm bọc bảo ôn: chọn độ dày theo đường kính ống và cách tính

Lớp nhôm bọc bên ngoài bảo ôn quyết định bảo ôn có khô và bền hay không. Bài viết đưa...

Công nghiệp phụ trợ ô tô: lắp ráp tăng 25%, linh kiện vẫn nhập

Công nghiệp phụ trợ ô tô: lắp ráp tăng 25%, linh kiện vẫn nhập

Sản lượng ô tô lắp ráp trong nước 10 tháng 2026 tăng 25,1%, nhưng nhập khẩu linh kiện...

Nhôm tấm 10mm: trọng lượng, dung sai, chọn mác và gia công

Nhôm tấm 10mm: trọng lượng, dung sai, chọn mác và gia công

Nhôm tấm 10mm là tấm bản dày dùng làm đế máy, bàn gá, bản mã chịu tải và chi tiết pha...

Triển lãm Vietbuild Hà Nội 11–14/11: xưởng nhôm kính nên xem gì

Triển lãm Vietbuild Hà Nội 11–14/11: xưởng nhôm kính nên xem gì

Triển lãm Quốc tế Vietbuild Hà Nội 2026 lần III diễn ra từ 11 đến 14/11 tại VEC Đông...

Nhôm tấm 5mm: trọng lượng, dung sai, chọn mác và gia công

Nhôm tấm 5mm: trọng lượng, dung sai, chọn mác và gia công

Nhôm tấm 5mm đủ cứng để làm sàn xe, đế máy, gá và bản mã chịu lực mà vẫn cắt, khoan,...

Giá nhôm tấm tuần 44/2026: SMM A00 nhích lên 23.780 CNY/tấn

Giá nhôm tấm tuần 44/2026: SMM A00 nhích lên 23.780 CNY/tấn

Giá nhôm thỏi SMM A00 chốt tuần 44/2026 ở 23.780 CNY/tấn ngày 30/10, cao hơn 110 CNY/...

Nhà máy alumin 2,4 triệu tấn ở Đồng Nai và giá nhôm tấm

Nhà máy alumin 2,4 triệu tấn ở Đồng Nai và giá nhôm tấm

Ngày 26/10/2026, CHALIECO công bố trúng gói tổng thầu EPC khoảng 833 triệu USD cho nh...

Nhôm tấm 1mm: trọng lượng, dung sai, chọn mác và cách kiểm hàng

Nhôm tấm 1mm: trọng lượng, dung sai, chọn mác và cách kiểm hàng

Nhôm tấm 1mm nhẹ, dễ cắt gấp nên được dùng nhiều cho vỏ tủ điện, hộp thiết bị, ốp tra...

Giá nhôm tấm tuần 43/2026: SMM A00 hồi lên 23.670 CNY/tấn

Giá nhôm tấm tuần 43/2026: SMM A00 hồi lên 23.670 CNY/tấn

Giá nhôm thỏi SMM A00 chốt tuần 43/2026 ở 23.670 CNY/tấn ngày 23/10, cao hơn 210 CNY/...

Vốn FDI đổ vào linh kiện điện tử miền Bắc: xưởng cơ khí cần gì

Vốn FDI đổ vào linh kiện điện tử miền Bắc: xưởng cơ khí cần gì

Ngày 21/10/2026, VIR đưa tin các nhà đầu tư nước ngoài tiếp tục rót hàng tỷ USD vào đ...

Call H&D
Send H&D an SMS
Directions to H&D
Contact H&D on Zalo
Message H&D on Messenger